P
PsychoCH2
Benutzer
- Registriert
- 16.12.2012
- Beiträge
- 3
- Punkte Reaktionen
- 0
Hersteller: HP (BenQ)
Typenbezeichnung: HSTND-2B03 (48.L1G02.A00)
kurze Fehlerbeschreibung (2-3 Worte): Bild verschwindet nach 2-3 Sekunden
Meine Messgeräte::
kein Messgerät
Analog/Digital Voltmeter
Oszilloskop
Schaltbild vorhanden?:
Nein
Hallo Zusammen
Ich habe hier einen HP Monitor mit einem Netzteilproblem, wie ich glaube.
Ich denke es ist der Leuchtstoffröhrentreiber, welcher probleme macht.
Ich habe schon einige TFTs mit den gleichen Symptomen Repariert, allerdings habe nun keine Idee mehr was es sein könnte.
Daher wende ich mich an Euch, in diesem Forum.
Es handelt sich um einen HP Monitor Typ: HSTND-2B03. Das Netzteil mit Lampenttreiber ist ein Benq Typ: 48.L1G02.A00.
(Oh je, diese BenQ-s.......)
Der Monitor schaltet ein, zeigt ein Bild für 2-3 sekunden, dann verwschwindet das Bild wieder. Normalerweise ist das ein Hintergrundbeleuchtungsproblem, allerdings habe ich was komisches beobachtet: Wenn das Bild verschwindet bleiben die Spannungen und die LED steht immer noch auf Grün, wenn ich aber mit einer Lampe in das Display leuchte ist kein Bild sichtbar, was normalerweise der Fall ist.
Am Netzteil habe ich 3.3V 5V und 18Volt. Ich habe die Spannungen mit dem Oszilloskop auf schwankungen und Ripple getestet, konnte nichts auffälliges finden, daher denke ich die Kondensatoren sollten IO sein.
Wenn die Hintergrundbeleuchtung während dem aufstarten angeht, sinkt die Spannung von 18Volt auf ca 15-16 Volt. Ich denke das ist normal.
Oder nicht?
Auch habe ich 2 Leitungen die vom Controller her kommen, es sind zwei getrennte Leitungen, einmal 3 Volt und einmal 3.3 Volt. Diese beiden leitungen haben immer noch 3 und 3.3 Volt nachdem das Bild weg ist, daher gehe ich davon aus dass es nicht das Controllboard ist. Dass das Controllboard das Startsignal gibt, und immer noch glaubt das alles in Ordnung ist.
Ich habe bereits alle Kontakte an den Transformern sowie den Transistoren 7505 und FETs vom Lampenschaltkreis nachgelötet.
Auch habe ich die 7505 auf Kurzschluss getestet, negativ. Dann habe ich mal die 7505 ersetzt, da ich dachte das es möglich ist dass einer unter Last den Dienst Quittiert. Negativ.
Meine Frage nun: Wie Teste ich die Hochspannungs-Trafos?
Wie Teste ich die Leuchtstoff-Lampen?
Auf der Netzteilplatine ist ein TI TL1451A, PWM Controller, welcher die Hintergrundbeleuchtung Steuert.
Soweit wie ich weiss haben die einen Zweikanal Feedback- Schaltkreis, welche dem Controller mitteilen ob die Schaltung funktioniert, oder ob ein Fehler vorliegt.
Wie finde ich heraus ob der TL1451 meine hintergrundbeleuchtung ausschaltet?
Aktuell habe ich PIN10 = OUT2 und PIN7 = OUT1 mit dem Oszilloskop unter die Lupe genommen.
Pin7/Out1 generiert ein schönes rechtecksignal während 2-3 Sekunden, dann hört es auf.
Pin10/Out2 generiert das selbe rechtecksignal, für etwa eine halbe bis eine Sekunde, und springt dann für 1-2 sekunden kontierlich auf High /ON bis dan der Monitor ausgeht.
Ist dass das Problem?
Ist der TL1451A defekt?
Vielen Dank schon im Voraus.
Gruss Simon
Und in Englisch:
Got a BenQ 48.L1G02.A00 Power Supply here, which is not working right. (Those benq`s.. oh la la)
The Monitor switches on, shows the picture, after 2-3 seconds it turns off again... Normaly, i think, this is backlight issue... What i dont understand, is, the monitors LED is still green, on, after the CCFL is off.
But if i Light with a Flashlight in to the TFT, i cannot see anything, all blank!
I tested all Voltages, ive Got 3.3V 5V and 18V. I testet with the oscilloscope, all stable and no Ripple, so also the condensers should be fine. If the Backlight turns on, on startup, the 18 Volts sink to about 15 to 16 Volt. I think this is normal, or isnt it? Then if got 2 Lines coming from the LVDS Controll panel, I think its two times +3.3 Volt, if the Power switch is pressed. This is ok, and stays on high / 3.3Volt, even after the picture is gone. For me this means, the Controll board is still saying lets go. I already resoldered the HV transformers, the 7505 Transistors and Fets. I also testet the 7505 for shorts, negative. I then replaced the 7505, because i think its possible that they fail, during the load cycle, negative. One of my questions: How to check the HV Transformers? How to Check the CCFL bulbs? On the Board there is a TI TL1451A, PWM controller wich controlls the background light. As i know they have a two chanel Feedbak cirquit, which lets the Controller know if the two Cirquits are working, otherwidse it switches of. How can i check if the 1451 is switching off my backlight? Actually i checked Pin 10 Out2 and pin7 Out 1 with the osciloscope. pin7 / Out1 Generates a nice and smoot square wave during2-3 seconds till it stops. Pin 10 / Out 2 generates the same square wave for about 1/2 to 1 second, then it goes to cntinous high till it stops.... Is this the problem? Is the TL1451A Faulty?
Thanks so far, in advance
Grreetings Simon
Typenbezeichnung: HSTND-2B03 (48.L1G02.A00)
kurze Fehlerbeschreibung (2-3 Worte): Bild verschwindet nach 2-3 Sekunden
Meine Messgeräte::
kein Messgerät
Analog/Digital Voltmeter
Oszilloskop
Schaltbild vorhanden?:
Nein
Hallo Zusammen
Ich habe hier einen HP Monitor mit einem Netzteilproblem, wie ich glaube.
Ich denke es ist der Leuchtstoffröhrentreiber, welcher probleme macht.
Ich habe schon einige TFTs mit den gleichen Symptomen Repariert, allerdings habe nun keine Idee mehr was es sein könnte.
Daher wende ich mich an Euch, in diesem Forum.
Es handelt sich um einen HP Monitor Typ: HSTND-2B03. Das Netzteil mit Lampenttreiber ist ein Benq Typ: 48.L1G02.A00.
(Oh je, diese BenQ-s.......)
Der Monitor schaltet ein, zeigt ein Bild für 2-3 sekunden, dann verwschwindet das Bild wieder. Normalerweise ist das ein Hintergrundbeleuchtungsproblem, allerdings habe ich was komisches beobachtet: Wenn das Bild verschwindet bleiben die Spannungen und die LED steht immer noch auf Grün, wenn ich aber mit einer Lampe in das Display leuchte ist kein Bild sichtbar, was normalerweise der Fall ist.
Am Netzteil habe ich 3.3V 5V und 18Volt. Ich habe die Spannungen mit dem Oszilloskop auf schwankungen und Ripple getestet, konnte nichts auffälliges finden, daher denke ich die Kondensatoren sollten IO sein.
Wenn die Hintergrundbeleuchtung während dem aufstarten angeht, sinkt die Spannung von 18Volt auf ca 15-16 Volt. Ich denke das ist normal.
Oder nicht?
Auch habe ich 2 Leitungen die vom Controller her kommen, es sind zwei getrennte Leitungen, einmal 3 Volt und einmal 3.3 Volt. Diese beiden leitungen haben immer noch 3 und 3.3 Volt nachdem das Bild weg ist, daher gehe ich davon aus dass es nicht das Controllboard ist. Dass das Controllboard das Startsignal gibt, und immer noch glaubt das alles in Ordnung ist.
Ich habe bereits alle Kontakte an den Transformern sowie den Transistoren 7505 und FETs vom Lampenschaltkreis nachgelötet.
Auch habe ich die 7505 auf Kurzschluss getestet, negativ. Dann habe ich mal die 7505 ersetzt, da ich dachte das es möglich ist dass einer unter Last den Dienst Quittiert. Negativ.
Meine Frage nun: Wie Teste ich die Hochspannungs-Trafos?
Wie Teste ich die Leuchtstoff-Lampen?
Auf der Netzteilplatine ist ein TI TL1451A, PWM Controller, welcher die Hintergrundbeleuchtung Steuert.
Soweit wie ich weiss haben die einen Zweikanal Feedback- Schaltkreis, welche dem Controller mitteilen ob die Schaltung funktioniert, oder ob ein Fehler vorliegt.
Wie finde ich heraus ob der TL1451 meine hintergrundbeleuchtung ausschaltet?
Aktuell habe ich PIN10 = OUT2 und PIN7 = OUT1 mit dem Oszilloskop unter die Lupe genommen.
Pin7/Out1 generiert ein schönes rechtecksignal während 2-3 Sekunden, dann hört es auf.
Pin10/Out2 generiert das selbe rechtecksignal, für etwa eine halbe bis eine Sekunde, und springt dann für 1-2 sekunden kontierlich auf High /ON bis dan der Monitor ausgeht.
Ist dass das Problem?
Ist der TL1451A defekt?
Vielen Dank schon im Voraus.
Gruss Simon
Und in Englisch:
Got a BenQ 48.L1G02.A00 Power Supply here, which is not working right. (Those benq`s.. oh la la)
The Monitor switches on, shows the picture, after 2-3 seconds it turns off again... Normaly, i think, this is backlight issue... What i dont understand, is, the monitors LED is still green, on, after the CCFL is off.
But if i Light with a Flashlight in to the TFT, i cannot see anything, all blank!
I tested all Voltages, ive Got 3.3V 5V and 18V. I testet with the oscilloscope, all stable and no Ripple, so also the condensers should be fine. If the Backlight turns on, on startup, the 18 Volts sink to about 15 to 16 Volt. I think this is normal, or isnt it? Then if got 2 Lines coming from the LVDS Controll panel, I think its two times +3.3 Volt, if the Power switch is pressed. This is ok, and stays on high / 3.3Volt, even after the picture is gone. For me this means, the Controll board is still saying lets go. I already resoldered the HV transformers, the 7505 Transistors and Fets. I also testet the 7505 for shorts, negative. I then replaced the 7505, because i think its possible that they fail, during the load cycle, negative. One of my questions: How to check the HV Transformers? How to Check the CCFL bulbs? On the Board there is a TI TL1451A, PWM controller wich controlls the background light. As i know they have a two chanel Feedbak cirquit, which lets the Controller know if the two Cirquits are working, otherwidse it switches of. How can i check if the 1451 is switching off my backlight? Actually i checked Pin 10 Out2 and pin7 Out 1 with the osciloscope. pin7 / Out1 Generates a nice and smoot square wave during2-3 seconds till it stops. Pin 10 / Out 2 generates the same square wave for about 1/2 to 1 second, then it goes to cntinous high till it stops.... Is this the problem? Is the TL1451A Faulty?
Thanks so far, in advance
Grreetings Simon
Zuletzt bearbeitet: